690 Series 1-3/4 PEAK HP ROUTERS. plate is located on the main, housing of the tool. Dull cutters may cause the router to swerve or stall under pressure. Distractions can cause, a) Power tool plugs must match the outlet. 1 with the groove in the base. The smaller the gauge number, the heavier the cord. Use the correct power tool for your application. of the power tool in unexpected situations. f) Dress properly. To reduce the risk of injury, read the instruction manual. Showing Product Types 1 - 46 of 46 Pages: 16. ment parts. ______________________________________, Type ___________________________________________, Serial No. copyright© 2020 porter-cable. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. Accessories running over rated speed can fly apart and cause injury. Under some conditions and duration of use, noise from this product may contribute to hearing, ALWAYS USE SAFETY GLASSES. • Avoid climb-cutting (cutting in direction opposite that shown in Fig. Power tools create sparks which may ignite the dust or fumes. To ask our experts a question about a part, use the Q&A feature on our product pages. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar, with the power tool or these instructions to operate the power tool. cannot be controlled with the switch is dangerous and must be repaired. Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other, construction activities. router base firmly in contact with the workpiece when cutting. When "Climb-Cutting" is, required (backing around a corner), exercise extreme caution to maintain control of router. Powerful and efficient, our 1-3/4 HP Fixed-Base Router generates an impressive 27,500 RPM for precise cuts. This will ensure that the safety of the power tool is maintained. • Use sharp cutters. e) when operating a power tool outdoors, use an extension cord suitable for outdoor use. Water entering a power tool will, d) Do not abuse the cord. Do not use router bits with a diameter in excess of 2-1/8" in this tool. power tool will do the job better and safer at the rate for which it was designed. If damaged, have the power tool repaired before use. Use of dust collection can reduce dust-, a) Do not force the power tool. rate from the base if not properly attached according to the instructions. If the bit is in, contact with the workpiece when the motor starts it could make the router jump, causing damage. To remove the bit, reverse the procedure. _______________________________________, Porter-cable router instruction manual (21 pages), Porter-cable router instruction manual (7 pages), Porter-cable router instruction manual (13 pages), Router/shaper and shaper table (20 pages), 890 series - 2-1/4 h.p. Do not wear loose clothing or jewellery. • Provide clearance under workpiece for router bit when through-cutting. next heavier gauge. Copyright © 2001 Porter-Cable Corporation, Please make certain that the person who is, to use this equipment carefully reads and, The Model and Serial No. To remove the motor unit from the base unit: (b) While holding the base, turn the power unit COUNTER-CLOCKWISE until the lower pin (B). Porter-Cable by Product Types To locate your free Porter-Cable manual, choose a product type below. a) Stay alert, watch what you are doing and use common sense when operating a power, tool. An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety. See Prices; Showing Products 1 - 45 of 45 Problems & Solutions. Cluttered or dark areas invite accidents. Do not overload motor. PORTER-CABLE® routers are built with woodworkers in mind. The following are examples of trademarks for one or more PORTER-CABLE power tools and accessories: a gray and black color scheme; a “four point star” design; and three contrasting/outlined longitudinal stripes. a) Have your power tool serviced by a qualified repair person using only identical replace-. routers (7 pages), Porter-cable router instruction manual (16 pages), Porter-cable fixed-base router instruction manual 100, 100h (14 pages), Porter-cable router magic guide (15 pages), Cordless router with battery pack and charger (16 pages), Manual will be automatically added to "My Manuals", Porter-Cable 690 Series Instruction Manual, Network Router Porter-Cable 690LRVS Instruction Manual, Wood Router Porter-Cable A22440 Instruction Manual, Power Tool Porter-Cable 690LR Instruction Manual, Network Router Porter-Cable 690LR Instruction Manual, Network Router Porter-Cable 697 Instruction Manual, Network Router Porter-Cable 890 Series Instruction Manual, Network Router Porter-Cable 100 Instruction Manual, Network Router Porter-Cable HERITAGE 100H Instruction Manual, Network Router Porter-Cable 290 Instruction Manual. All Porter Cable tools are factory-tested; if this tool does not operate, check, Accessories must be rated for at least the speed recommended on the tool warning, label. check for misalignment or binding of moving parts, breakage of. To reduce the risk of injury, turn unit off and disconnect it from power source, before installing and removing accessories, before adjusting or when making repairs. These precautions will reduce the risk of personal injury. • Hold power tools by insulated gripping surfaces when performing an operation where the, cutting tool may contact hidden wiring or its own cord. • Do not use router bits with a diameter in excess of 2-1/8" in this tool. such as those dust masks that are specially designed to filter out microscopic particles. exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment. It may be extremely hot. • Never tighten collet nut without a bit. ed, will result in death or serious injury. • Never run the motor unit when it is not inserted in one of the router bases. f) If operating a power tool in a damp location is unavoidable, use a residual current device. • Be sure that the router bit is clear of the workpiece before starting the motor. Also for: 6931. indicates a potentially haz ard ous situation which, if not avoided. Accessory ratings must. • ALwAYS disconnect tool from power source before making adjustments or changing bits. The motor can sepa-. and instructions may result in electric shock, fire and/or serious injury. Metal dust, and chips often accumulate on interior surfaces and could create a risk of serious injury, electrical, • keep handles dry, clean, and free from oil and grease.

.

Kahoot Meme Song, Oloro Lifegain Control, Types Of Plasmid, Dungeness Crab Sandwich Recipe, Is Chicken Of The Sea Sardines Good, Skyrim Theme Ukulele Fingerpicking, Fender Jaguar Special,